480 cambelt cover

Cleaned up the garage and found some parts you want to sell? Or are you looking for that one part? You can advertise or request just about anything that has to do with the Volvo 480 in here: brochures, towing-hooks, antenna's, etc etc...

Moderators: jifflemon, coyote1980, Rachel

Post Reply
john denmead
480 Newbie
Posts: 35
Joined: Sat Nov 02, 2002 5:40 pm
Location: dorset uk

480 cambelt cover

Post by john denmead » Tue Apr 14, 2020 6:27 pm

Can anyone help I am after cambelt cover front and back there are three parts to cover front cover 3343732,cover upper 3344548, casing lower 3343735 casing lower is the main one I need but all would be helpful.Any info would be great.
cheers john.

malkontent
Can tell where the 480 was built
Posts: 374
Joined: Fri Jan 15, 2010 1:20 pm
Location: Cracow , Poland

Re: 480 cambelt cover

Post by malkontent » Thu Apr 16, 2020 6:01 pm

Hi
Lucky you , I have some covers . Must check .
regards
Marek

malkontent
Can tell where the 480 was built
Posts: 374
Joined: Fri Jan 15, 2010 1:20 pm
Location: Cracow , Poland

Re: 480 cambelt cover

Post by malkontent » Fri Apr 17, 2020 3:55 pm

In my treasures I found two covers , one plastic with Renault part number / 77....../ and second short / metal / without part number . Vadis says that You have B18E , ED , ES , EP , am I right ? You need inner and outer casings . Best for me , send VIN please . I`m charging my camera , so maybe today You will have pictures .
best
Marek

malkontent
Can tell where the 480 was built
Posts: 374
Joined: Fri Jan 15, 2010 1:20 pm
Location: Cracow , Poland

Re: 480 cambelt cover

Post by malkontent » Mon Apr 20, 2020 3:27 pm

covers : outer / plastic / 7700857429 , inner / plastic / 7700741120 , inner / metal / 7700598397 .Motor B18EP 115 , C030103 .
Image
Image

I need a cog wheel puller / small / , / ordered / must wait 2 or 3 days .

jifflemon
480 Is my middle name
Posts: 2464
Joined: Sat Dec 17, 2016 11:03 am

Re: 480 cambelt cover

Post by jifflemon » Mon Apr 20, 2020 7:32 pm

You could use 5mm bolts, drilled through a flat plate to draw the pulley off.

malkontent
Can tell where the 480 was built
Posts: 374
Joined: Fri Jan 15, 2010 1:20 pm
Location: Cracow , Poland

Re: 480 cambelt cover

Post by malkontent » Mon Apr 20, 2020 8:48 pm

It works but only on a bigger cog , for smaller you need a puller .

john denmead
480 Newbie
Posts: 35
Joined: Sat Nov 02, 2002 5:40 pm
Location: dorset uk

Re: 480 cambelt cover

Post by john denmead » Tue Apr 21, 2020 1:57 pm

Hi thanks very much for replying to my post I am pleased to say I now have the covers I need.
Cheers
John.

malkontent
Can tell where the 480 was built
Posts: 374
Joined: Fri Jan 15, 2010 1:20 pm
Location: Cracow , Poland

Re: 480 cambelt cover

Post by malkontent » Fri Apr 24, 2020 3:56 pm

Image
someone was before me , no gasket , a lot of silicon , not resistant of diesel fuel and oil !
Image
Covers ! Unfortunately , small plastic cover is cracked , it`s a gift for you . Puller I ordered for a small cog is not suitable , but ... two bolts maybe works , Vadis says..... PULLER !They give only a part number , without a picture .

malkontent
Can tell where the 480 was built
Posts: 374
Joined: Fri Jan 15, 2010 1:20 pm
Location: Cracow , Poland

Re: 480 cambelt cover

Post by malkontent » Wed May 20, 2020 12:59 pm

Still no gasket , and a butcher was there
Image
Image
Image

Crankshaft seal 50 x 68 x 8
Gear seal 30 x 40 x 7

malkontent
Can tell where the 480 was built
Posts: 374
Joined: Fri Jan 15, 2010 1:20 pm
Location: Cracow , Poland

Re: 480 cambelt cover

Post by malkontent » Fri Jun 26, 2020 12:23 pm

Image
simmering made some grooves

Post Reply