Plasma cutter < £80
Moderators: jifflemon, coyote1980, Rachel
Plasma cutter < £80
Nowt to do with me
check Lidl
https://www.lidl.co.uk/en/c/diy/c1355
or
https://www.lidl.co.uk/en/p/diy/parksid ... ter/p29579
and unbiased opinion
https://www.mig-welding.co.uk/forum/thr ... ter.89053/
check Lidl
https://www.lidl.co.uk/en/c/diy/c1355
or
https://www.lidl.co.uk/en/p/diy/parksid ... ter/p29579
and unbiased opinion
https://www.mig-welding.co.uk/forum/thr ... ter.89053/
Alan
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
Re: Plasma cutter < £80
nice find!
-
- Can tell where the 480 was built
- Posts: 316
- Joined: Sat Jan 11, 2014 3:44 pm
- Location: Aberdeenshire, Huntly
Re: Plasma cutter < £80
I have the better half poised to search all 3 Lidl's on her way home from work in Dyce - old Aberdeen on Thursday
'91 480 ES 2.0l 16v 'Williams' Conversion - 212bhp/230nm
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium
Re: Plasma cutter < £80
I hope she works nights, because stuff like this is normally off the shelves on Listed on Ebay by 9am!
-
- Can tell where the 480 was built
- Posts: 316
- Joined: Sat Jan 11, 2014 3:44 pm
- Location: Aberdeenshire, Huntly
Re: Plasma cutter < £80
Ah but there are the joys of low population density Scotland
"They may take our lives, but they will never take our middle aisle bargains!"
"They may take our lives, but they will never take our middle aisle bargains!"
'91 480 ES 2.0l 16v 'Williams' Conversion - 212bhp/230nm
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium
Re: Plasma cutter < £80
was on the Reliant web forum, usually filed in the 'today at Lidl /Aldi' section . .. . .
Good news, so I know where to go if I need some steel cut to fancy shapes???
Alan
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
-
- Can tell where the 480 was built
- Posts: 316
- Joined: Sat Jan 11, 2014 3:44 pm
- Location: Aberdeenshire, Huntly
Re: Plasma cutter < £80
IF i get it aye!
but my work is thinking on installing a CNC plasma table... so then you can have multitudes of fancy cut shapes!!
but my work is thinking on installing a CNC plasma table... so then you can have multitudes of fancy cut shapes!!
'91 480 ES 2.0l 16v 'Williams' Conversion - 212bhp/230nm
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium
Re: Plasma cutter < £80
then you need to programme the CNC rather than just follow the chalk line?
Alan
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
-
- Can tell where the 480 was built
- Posts: 316
- Joined: Sat Jan 11, 2014 3:44 pm
- Location: Aberdeenshire, Huntly
Re: Plasma cutter < £80
i'm qualified in drawing CNC lines, but ironically not chalk lines
'91 480 ES 2.0l 16v 'Williams' Conversion - 212bhp/230nm
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium