B20F Engine (+ poss engine loom and ECU)

Cleaned up the garage and found some parts you want to sell? Or are you looking for that one part? You can advertise or request just about anything that has to do with the Volvo 480 in here: brochures, towing-hooks, antenna's, etc etc...

Moderators: jifflemon, coyote1980, Rachel

Post Reply
cranna21
Can tell where the 480 was built
Posts: 313
Joined: Sat Jan 11, 2014 3:44 pm
Location: Aberdeenshire, Huntly

B20F Engine (+ poss engine loom and ECU)

Post by cranna21 » Thu Jul 04, 2019 8:19 am

Hi folks,

Got a B20F engine for sale - running and on 138k miles looking for £150 and for this you get:

Engine - bare with no ancillaries but comes with inlet and exhaust manifold/downpipe
Sensors - sensors required to run the engine but not those that supply signal to the info centre (keeping these as spares)
Coil Pack
Wiring loom - engine loom only not full car loom
ECU

I'm located in NE Scotland about an hour from Aberdeen and I can arrange to have it palletised if need be however collection preferred but I understand that's probably an impracticality!

any questions - just ask!
'91 480 ES 2.0l 16v 'Williams' Conversion - 212bhp/230nm
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium

Alan 480
480 Is my middle name
Posts: 1489
Joined: Sun Aug 28, 2011 9:03 am
Location: Aberdeen

Re: B20F Engine (+ poss engine loom and ECU)

Post by Alan 480 » Thu Jul 04, 2019 11:43 am

Fraser

What would you charge for storage of said engine etc?

now that I have a pair of 480 and both have high mileage a spare could be useful:-) ditto gearbox in red one is getting 'dour' to engage first/second

I have some room under the freezer now that the Regal engine/box have left for new owner, but unsure if the engine would fit in that space :-)
Alan

480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1

cranna21
Can tell where the 480 was built
Posts: 313
Joined: Sat Jan 11, 2014 3:44 pm
Location: Aberdeenshire, Huntly

Re: B20F Engine (+ poss engine loom and ECU)

Post by cranna21 » Thu Jul 04, 2019 12:09 pm

Hi Alan!

I'd need to assess space myself! that's partly my reason for a wee clear out! haha, would you like me to do a measure? i'll be at the unit tomorrow night so can measure it all up if you required, had planned on keeping the box as a spare but I've got another 2 from 1.7's that "would do if required" as spares for myself so you'd be more than welcome to this one - saves me the job of removing it! haha
'91 480 ES 2.0l 16v 'Williams' Conversion - 212bhp/230nm
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium

cranna21
Can tell where the 480 was built
Posts: 313
Joined: Sat Jan 11, 2014 3:44 pm
Location: Aberdeenshire, Huntly

Re: B20F Engine (+ poss engine loom and ECU)

Post by cranna21 » Thu Jul 04, 2019 1:12 pm

Alan,

I forgot to mention, I have a lad needing an ECU urgently, do you need the one I have listed here? if no then we could maybe do same price as above but rather than the ECU you get the box! your call happy to discuss :)
'91 480 ES 2.0l 16v 'Williams' Conversion - 212bhp/230nm
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium

Alan 480
480 Is my middle name
Posts: 1489
Joined: Sun Aug 28, 2011 9:03 am
Location: Aberdeen

Re: B20F Engine (+ poss engine loom and ECU)

Post by Alan 480 » Thu Jul 04, 2019 4:59 pm

Fraser
yep I saw the 'need for ECU' post,
if you measure the rough length then seems fair enough, just don't tell the other half!

I can measure space I have/had as there is a trolley jack and spare gearbox (probabbly going scrap) in the place at present etc

I assume the engine 'was running' ? no funny noises from within?
Alan

480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1

cranna21
Can tell where the 480 was built
Posts: 313
Joined: Sat Jan 11, 2014 3:44 pm
Location: Aberdeenshire, Huntly

Re: B20F Engine (+ poss engine loom and ECU)

Post by cranna21 » Thu Jul 04, 2019 7:39 pm

Hi Alan!

Turns out hes found an ecu, so all available!

Will get it measured tomorrow for you!
'91 480 ES 2.0l 16v 'Williams' Conversion - 212bhp/230nm
'90 940 GL 2.0l Estate
'08 XC90 D5 SE Premium

Post Reply