Plasma cutter < £80

Cleaned up the garage and found some parts you want to sell? Or are you looking for that one part? You can advertise or request just about anything that has to do with the Volvo 480 in here: brochures, towing-hooks, antenna's, etc etc...

Moderators: jifflemon, coyote1980, Rachel

Post Reply
Alan 480
480 Is my middle name
Posts: 1124
Joined: Sun Aug 28, 2011 9:03 am
Location: Aberdeen

Plasma cutter < £80

Post by Alan 480 » Mon Feb 10, 2020 7:08 pm

Alan

480 ES 2litre x 2, C30 1.8ES, SS1

jifflemon
480 Is my middle name
Posts: 1468
Joined: Sat Dec 17, 2016 11:03 am

Re: Plasma cutter < £80

Post by jifflemon » Mon Feb 10, 2020 8:16 pm

nice find! :D

cranna21
Knows an Aerodeck isn't a 480
Posts: 265
Joined: Sat Jan 11, 2014 3:44 pm
Location: Aberdeenshire, Huntly

Re: Plasma cutter < £80

Post by cranna21 » Tue Feb 11, 2020 7:12 am

I have the better half poised to search all 3 Lidl's on her way home from work in Dyce - old Aberdeen on Thursday :rofl:
'91 480 ES 2.0l 16v 'Williams' Conversion - 208bhp/230nm
'91 940 GL 2.0l Estate
'09 C30 2.0d R-Design

jifflemon
480 Is my middle name
Posts: 1468
Joined: Sat Dec 17, 2016 11:03 am

Re: Plasma cutter < £80

Post by jifflemon » Tue Feb 11, 2020 7:58 am

I hope she works nights, because stuff like this is normally off the shelves on Listed on Ebay by 9am!

cranna21
Knows an Aerodeck isn't a 480
Posts: 265
Joined: Sat Jan 11, 2014 3:44 pm
Location: Aberdeenshire, Huntly

Re: Plasma cutter < £80

Post by cranna21 » Tue Feb 11, 2020 10:24 am

Ah but there are the joys of low population density Scotland ;)

"They may take our lives, but they will never take our middle aisle bargains!"
'91 480 ES 2.0l 16v 'Williams' Conversion - 208bhp/230nm
'91 940 GL 2.0l Estate
'09 C30 2.0d R-Design

Alan 480
480 Is my middle name
Posts: 1124
Joined: Sun Aug 28, 2011 9:03 am
Location: Aberdeen

Re: Plasma cutter < £80

Post by Alan 480 » Tue Feb 11, 2020 12:56 pm

jifflemon wrote:
Mon Feb 10, 2020 8:16 pm
nice find! :D
was on the Reliant web forum, usually filed in the 'today at Lidl /Aldi' section . .. . .
cranna21 wrote:
Tue Feb 11, 2020 10:24 am
Ah but there are the joys of low population density Scotland ;)

"They may take our lives, but they will never take our middle aisle bargains!"
Good news, so I know where to go if I need some steel cut to fancy shapes???
Alan

480 ES 2litre x 2, C30 1.8ES, SS1

cranna21
Knows an Aerodeck isn't a 480
Posts: 265
Joined: Sat Jan 11, 2014 3:44 pm
Location: Aberdeenshire, Huntly

Re: Plasma cutter < £80

Post by cranna21 » Tue Feb 11, 2020 1:39 pm

IF i get it aye!

but my work is thinking on installing a CNC plasma table... so then you can have multitudes of fancy cut shapes!!
'91 480 ES 2.0l 16v 'Williams' Conversion - 208bhp/230nm
'91 940 GL 2.0l Estate
'09 C30 2.0d R-Design

Alan 480
480 Is my middle name
Posts: 1124
Joined: Sun Aug 28, 2011 9:03 am
Location: Aberdeen

Re: Plasma cutter < £80

Post by Alan 480 » Thu Feb 20, 2020 12:44 pm

cranna21 wrote:
Tue Feb 11, 2020 1:39 pm
IF i get it aye!

but my work is thinking on installing a CNC plasma table... so then you can have multitudes of fancy cut shapes!!
then you need to programme the CNC rather than just follow the chalk line? :?
Alan

480 ES 2litre x 2, C30 1.8ES, SS1

cranna21
Knows an Aerodeck isn't a 480
Posts: 265
Joined: Sat Jan 11, 2014 3:44 pm
Location: Aberdeenshire, Huntly

Re: Plasma cutter < £80

Post by cranna21 » Thu Feb 20, 2020 1:09 pm

i'm qualified in drawing CNC lines, but ironically not chalk lines :rofl:
'91 480 ES 2.0l 16v 'Williams' Conversion - 208bhp/230nm
'91 940 GL 2.0l Estate
'09 C30 2.0d R-Design

Post Reply