rear bumper bolts
Moderators: jifflemon, coyote1980, Rachel
rear bumper bolts
Any tips on removing the 4 bolts that hold on the rear bumper if they are horrifically rusted on? Have tried (in order of violence) wd40, socket wrench, tap with hammer, socket with breaker bar... there isnt room for an angle grinder, would a dremel be upto the job of ether cutting as bolt or making enough of a ridge that a chisel and hammer could be used? Any ideas?
Best
Tim
(obv if any of you have a handy bumper and want to save me a job thats an option too )
Best
Tim
(obv if any of you have a handy bumper and want to save me a job thats an option too )
Re: rear bumper bolts
You had a blow torch on them yet?
I usually go cherry red, then spray with WD40 as it's dulled off (just be careful, it is flammable!)
The heat expands it, the fluid can then really penetrate
I usually go cherry red, then spray with WD40 as it's dulled off (just be careful, it is flammable!)
The heat expands it, the fluid can then really penetrate
Re: rear bumper bolts
yep, that's one way
I think I used 'brute force' as above, then LOTS of grease when re-attached it!!
Alan
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
Re: rear bumper bolts
Ive not set fire to them yet, in fact as I'm not actively a Gordan Ramsey fan I dont own a blow torch! This isn't my 480 which has already had it bumper 'repaired' but a tragic donor car, the owner would run out an extension lead for me so I have electrics if needed. Has anyone ever cut a bolt with a dremel type tool? Is it possible?
Re: rear bumper bolts
very slow progress, id reckontimrosser wrote: ↑Tue Nov 27, 2018 9:48 pmIve not set fire to them yet, in fact as I'm not actively a Gordan Ramsey fan I dont own a blow torch! This isn't my 480 which has already had it bumper 'repaired' but a tragic donor car, the owner would run out an extension lead for me so I have electrics if needed. Has anyone ever cut a bolt with a dremel type tool? Is it possible?
can you 'centre dab' it
drill it
then split nut?
nothing to lose, assumes you can get to a flat?
Alan
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
Re: rear bumper bolts
Got an electric heat gun then? You know, the sort of thing used for paint stripping?timrosser wrote: ↑Tue Nov 27, 2018 9:48 pmIve not set fire to them yet, in fact as I'm not actively a Gordan Ramsey fan I dont own a blow torch! This isn't my 480 which has already had it bumper 'repaired' but a tragic donor car, the owner would run out an extension lead for me so I have electrics if needed. Has anyone ever cut a bolt with a dremel type tool? Is it possible?
You could always buy one of these, but I think it *may* be a tad overkill....
They're unbelievably useful though!
Re: rear bumper bolts
worth a try, always been frightened of breaking 'stud extractors' in the bolt hole but in this case if these broke they'd just fall of so no damage done, except to the nuts, or possibly just shear off the studarthuy wrote: ↑Fri Nov 30, 2018 7:06 pmI use bolt grips,
https://www.google.co.uk/search?q=bolt+ ... ie=plaji-i
https://www.screwfix.com/p/erbauer-bolt ... -pcs/6083d
they seemed to geta decnet write up!
Alan
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
480 ES 2litre 'Celebration' ? , C30 1.8ES, SS1
Re: rear bumper bolts
Have a set of irwin ones very similar.
As you've already mentioned though, the risk is that you fix one problem, only to give yourself another (nuts are off, but now you've got studs to replace!)
I'd seriously consider heat as the next move.
As you've already mentioned though, the risk is that you fix one problem, only to give yourself another (nuts are off, but now you've got studs to replace!)
I'd seriously consider heat as the next move.
Re: rear bumper bolts
Have gone with some metric nut removers & a butane culinary flame thrower- I'll let you know how it works out! Thanks for all the tips
<3
<3